<div>Bom dia à todos,</div>
<div> </div>
<div> Não estou conseguindo fazer funcionar a minha placa VB6060 da Digivoice com Asterisk. Eu já baixei o dgvchannel e o voicerlib e segui o manual para instalação. Quando eu starto o asterisk eu recebo as seguintes mensagens abaixo e trava a máquina:
</div>
<div> </div>
<div>
<div><font face="Arial" size="2">#########################################################</font></div>
<div><font face="Arial" size="2"> [chan_dgv.so] => (Digivoice Boards Support)<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3361 load_module: load_module: starting for Dgv<br> == Parsing '/etc/asterisk/digivoice.conf': Found
<br> == Registered channel type 'Dgv' (Digivoice voice cards Driver)<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3023 setup_dgv: Dgv Channel: SLINEAR support disabled<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3027 setup_dgv: Dgv Channel: U_LAW support disabled
<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3031 setup_dgv: Dgv Channel: A_LAW support disabled<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3035 setup_dgv: Dgv Channel: GSM support enabled<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3039 setup_dgv: Dgv Channel: Force Single Span - no
<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3106 setup_dgv: Configurations for Dgv Channel:<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3107 setup_dgv: default detectiontype = 1<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3108 setup_dgv: ringbacktone1 = tone1 (5)
<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3109 setup_dgv: ringbacktone2 = tone1 (5)<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3110 setup_dgv: busytone1 = tone1 (5)<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3111 setup_dgv: busytone2 = tone1 (5)
<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3114 setup_dgv: ringback_times[0] = 1000<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3114 setup_dgv: ringback_times[1] = 4000<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3114 setup_dgv: ringback_times[2] = 1000
<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3116 setup_dgv: busy_times[0] = 1000<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3116 setup_dgv: busy_times[1] = 4000<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3116 setup_dgv: busy_times[2] = 1000
<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3119 setup_dgv: default_call_progress = cp_1232d.cfg<br>Aug 28 17:44:49 NOTICE[5200]: chan_dgv.c:3129 setup_dgv: audio capabilities = 2<br>vlibd->init_plx: Probing Device Name: vlibd
<br>vlibd->plx_countcards: 1 Cards Found<br>vlibd->plx_probe: ->Probing card number 0<br>ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 169<br></font></div>
<div><font face="Arial" size="2">
<div><font face="Arial" size="2">#########################################################</font></div>
<div> </div>
<div> Não consigo saber o que está dando de errado. Já cheguei a formatar a máquina e comerçar do zero, porém sempre que tento startar o asterisk acaba travando a máquina. Se eu remover o chan_dgv.so do diretório modules o asterisk carrega normalmente.
</div>
<div> </div>
<div> Agradeço qualquer ajuda.</div>
<div> </div>
<div> Sds,</div>
<div> </div>
<div> Alessandro</div></font></div></div>