Re: [AsteriskBrasil] digium card não funciona

Ralph Liebessohn ralphliebessohn em gmail.com
Segunda Agosto 14 08:33:02 BRT 2006


On 8/14/06, Fabio Vasco <fabiohvgomes em hotmail.com> wrote:
>
> Ralph,
> /etc/zaptel.conf e /etc/asterisk/zapata.conf
> zttool
> lspci -v
> Deixa a gente ver isso...
> Que Linux vc. está usando?
> Abraços,
> FHV
>
> >From: "Ralph Liebessohn" <ralphliebessohn em gmail.com>
> >Reply-To: asteriskbrasil em listas.asteriskbrasil.org
> >To: asteriskbrasil em listas.asteriskbrasil.org
> >Subject: [AsteriskBrasil] digium card não funciona
> >Date: Fri, 11 Aug 2006 16:50:28 +0000
> >
> >boa tarde,
> >
> >
> >pessoal, estou com um probleminha aqui com uma placa da digium.
> >Inicialmente comecei com o asterisk em um computador comum sempron com
> >placa
> >mãe pcchips e coloquei pra funcionar uma TE406P. Até ai tudo lindo.
> >Agora colocando o asterisk pra rodar num P4 Dual com placa mãe intel
> >(d101ggc) tudo aparentemente funciona, o asterisk compila, roda, liga de
> >sip
> >pra sip, os modulos zaptel compilam, carregam, configuram, mas na hora de
> >ligar mesmo PAM !
> >Recebo isso.
> >
> >Connected to Asterisk 1.2.7.1 currently running on astk (pid = 4174)
> >Verbosity is at least 99
> >Core debug is at least 99
> >    -- Executing Dial("SIP/12347-1574", "ZAP/g1/21226551") in new stack
> >    -- Requested transfer capability: 0x00 - SPEECH
> >    -- Called g1/21226551
> >  == Primary D-Channel on span 1 down
> >Aug 11 12:05:11 WARNING[4219]: chan_zap.c:2298 pri_find_dchan: No
> >D-channels
> >available!  Using Primary channel 16 as D-channel anyway!
> >    -- Hungup 'Zap/1-1'
> >  == Everyone is busy/congested at this time (1:0/0/1)
> >    -- Executing Hangup("SIP/12347-1574", "") in new stack
> >  == Primary D-Channel on span 1 down
> >Aug 11 12:05:14 WARNING[4219]: chan_zap.c:2298 pri_find_dchan: No
> >D-channels
> >available!  Using Primary channel 16 as D-channel anyway!
> >
> >Saída /var/log/asterisk/full:
> >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Allocating new SIP dialog for
> >ff3e5bab-e0089797 em 192.168.11.192 - INVITE (With RTP)
> >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: **** Received INVITE (5) -
> Command
> >in SIP INVITE
> >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: * SIP extension value: 0 for call
> >ff3e5bab-e0089797 em 192.168.11.192
> >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Setting NAT on RTP to 524288
> >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: = Found Their Call ID:
> >ff3e5bab-e0089797 em 192.168.11.192 Their Tag 53fbac9bdac9fb67o1
> >Our tag: as0681a10d
> >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: **** Received ACK (6) - Command
> in
> >SIP ACK
> >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Stopping retransmission on '
> >ff3e5bab-e0089797 em 192.168.11.192' of Response 101: Match
> >Found
> >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: = Found Their Call ID:
> >ff3e5bab-e0089797 em 192.168.11.192 Their Tag 53fbac9bdac9fb67o1
> >Our tag: as0681a10d
> >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: **** Received INVITE (5) -
> Command
> >in SIP INVITE
> >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: * SIP extension value: 0 for call
> >ff3e5bab-e0089797 em 192.168.11.192
> >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Setting NAT on RTP to 524288
> >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Checking SIP call limits for
> device
> >12347
> >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Updating call counter for
> incoming
> >call
> >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: build_route: Contact hop: Linksys
> 2
> ><sip:12347 em 192.168.11.192:5061>
> >Aug 11 11:53:31 DEBUG[4315] chan_sip.c: Checking device state for peer
> >12347
> >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for SIP/12347 -
> >state 2 (In use)
> >Aug 11 11:53:31 DEBUG[4610] pbx.c: Launching 'Dial'
> >Aug 11 11:53:31 VERBOSE[4610] logger.c:     -- Executing
> >Dial("SIP/12347-d99a", "ZAP/g1/21226551") in new stack
> >Aug 11 11:53:31 DEBUG[4610] chan_zap.c: Using channel 1
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable
> >STACK-default-21226551-1.
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPCALLID.
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPUSERAGENT.
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPDOMAIN.
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPURI.
> >Aug 11 11:53:31 VERBOSE[4610] logger.c:     -- Requested transfer
> >capability: 0x00 - SPEECH
> >Aug 11 11:53:31 VERBOSE[4610] logger.c:     -- Called g1/21226551
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel Zap/1-1 to read format
> >slin
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel SIP/12347-d99a to
> write
> >format slin
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel SIP/12347-d99a to read
> >format slin
> >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel Zap/1-1 to write
> format
> >slin
> >Aug 11 11:53:31 DEBUG[4611] app_queue.c: Device 'SIP/12347' changed to
> >state
> >'2' (In use)
> >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
> state
> >2 (In use)
> >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
> state
> >2 (In use)
> >Aug 11 11:53:31 DEBUG[4612] app_queue.c: Device 'Zap/1' changed to state
> >'2'
> >(In use)
> >Aug 11 11:53:31 DEBUG[4613] app_queue.c: Device 'Zap/1' changed to state
> >'2'
> >(In use)
> >Aug 11 11:53:31 DEBUG[4610] rtp.c: Ooh, format changed from unknown to
> ulaw
> >Aug 11 11:53:34 VERBOSE[4364] logger.c:   == Primary D-Channel on span 1
> >down
> >Aug 11 11:53:34 WARNING[4364] chan_zap.c: No D-channels available!  Using
> >Primary channel 16 as D-channel anyway!
> >Aug 11 11:53:34 DEBUG[4610] channel.c: Hanging up channel 'Zap/1-1'
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: zt_hangup(Zap/1-1)
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option AUDIO MODE, value:
> ON(1)
> >on Zap/1-1
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Hangup: channel: 1 index = 0,
> >normal
> >= 22, callwait = -1, thirdcall = -1
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: disabled echo cancellation on
> >channel 1
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option TDD MODE, value:
> OFF(0)
> >on Zap/1-1
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Updated conferencing on 1, with 0
> >conference users
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option AUDIO MODE, value:
> >OFF(0)
> >on Zap/1-1
> >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: disabled echo cancellation on
> >channel 1
> >Aug 11 11:53:34 VERBOSE[4610] logger.c:     -- Hungup 'Zap/1-1'
> >Aug 11 11:53:34 VERBOSE[4610] logger.c:   == Everyone is busy/congested
> at
> >this time (1:0/0/1)
> >Aug 11 11:53:34 DEBUG[4610] app_dial.c: Exiting with
> >DIALSTATUS=CHANUNAVAIL.
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Launching 'Hangup'
> >Aug 11 11:53:34 VERBOSE[4610] logger.c:     -- Executing
> >Hangup("SIP/12347-d99a", "") in new stack
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Spawn extension (default,21226551,2)
> >exited non-zero on 'SIP/12347-d99a'
> >Aug 11 11:53:34 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
> state
> >0 (Unknown)
> >Aug 11 11:53:34 DEBUG[4614] app_queue.c: Device 'Zap/1' changed to state
> >'0'
> >(Unknown)
> >Aug 11 11:53:34 DEBUG[4610] cdr_pgsql.c: cdr_pgsql: inserting a CDR
> record.
> >Aug 11 11:53:34 DEBUG[4610] cdr_pgsql.c: cdr_pgsql: SQL command executed:
> >INSERT INTO cdr (calldate,clid,src,dst,dcontext,ch
>
> >annel,dstchannel,lastapp,lastdata,duration,billsec,disposition,amaflags,accountcode,uniqueid,userfield)
> >VALUES ('2006-08-11 1
> >1:53:31','"Linksys 2" <12347>','12347','21226551','default',
> >'SIP/12347-d99a','Zap/1-1','Hangup','',3,0,'NO ANSWER',2,'12347'
> >,'1155308011.4','')
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '"Linksys 2"
> <12347>'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '12347'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '21226551'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'default'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'SIP/12347-d99a'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'Zap/1-1'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'Hangup'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '(null)'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '2006-08-11
> 11:53:31'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '(null)'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '2006-08-11
> 11:53:34'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '3'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '0'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'NO ANSWER'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'BILLING'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '12347'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '1155308011.4'
> >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '(null)'
> >Aug 11 11:53:34 DEBUG[4610] channel.c: Hanging up channel
> 'SIP/12347-d99a'
> >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: Hangup call SIP/12347-d99a, SIP
> >callid ff3e5bab-e0089797 em 192.168.11.192)
> >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: update_call_counter(12347) -
> >decrement call limit counter
> >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: Updating call counter for
> incoming
> >call
> >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: AST hangup cause 16 (no match
> found
> >in SIP)
> >Aug 11 11:53:34 DEBUG[4315] chan_sip.c: Checking device state for peer
> >12347
> >Aug 11 11:53:34 DEBUG[4315] devicestate.c: Changing state for SIP/12347 -
> >state 1 (Not in use)
> >Aug 11 11:53:34 DEBUG[4615] app_queue.c: Device 'SIP/12347' changed to
> >state
> >'1' (Not in use)
> >
> >Ele simplesmente liga, chia e corta a ligação imediatamente, a partir daí
> >as
> >ligações pelo E1 não se realizam mais.
> >
> >NOTICE[4981]: app_dial.c:1029 dial_exec_full: Unable to create channel of
> >type 'ZAP' (cause 34 - Circuit/channel congestion)
> >  == Everyone is busy/congested at this time (1:0/1/0)
> >
> >Receber ligação de forma nenhuma.
> >As mesmas configurações (trocando o hd de máquina) funciona
> perfeitamente.
> >Já tentei usar também com outra placa intel e um p4 HT sem dual core, mas
> a
> >falha permaneceu.
> >Já vi algumas coisas parecidas na lista mas nada que chegue ao amago
> dessa
> >questao.
> >Alguem já viu algo parecido? Tem alguma idéia do que possa ser feito para
> o
> >sistema completo funcionar?
> >
> >
> >--
> >Ralph Liebessohn
> >ICQ: 74835911
> >Skype: liebessohn
>


Oi Fábio,


vamos as configurações.
astk:/etc# cat /etc/zaptel.conf

span=1,0,1,ccs,hdb3,crc4,yellow
#span=2,0,1,ccs,hdb3,crc4,yellow
#span=3,0,1,ccs,hdb3,crc4,yellow
#span=4,0,1,ccs,hdb3,crc4,yellow

bchan=1-15,17-31
dchan=16

#bchan=32-46,48-62
#dchan=47

#bchan=63-77,79-93
#dchan=78

#bchan=94-108,110-124
#dchan=109

loadzone = us
loadzone = br
defaultzone = br


astk:/etc# cat /etc/asterisk/zapata.conf
[trunkgroups]

[channels]
context=default
switchtype=national
pridialplan=international
;signalling=pri_cpe
rxwink=300              ; Atlas seems to use long (250ms) winks
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=yes
echotraining=400
rxgain=0.0
txgain=0.0

group=1
callgroup=1
pickupgroup=1
immediate=no
transfertobusy=no

signalling=pri_cpe

channel => 1-15,17-31
;channel => 32-46,48-62,63-77,79-93
;channel => 94-108,110-124

astk:/etc# zttool
Alarms          Span
OK              T4XXP (PCI) Card 0 Span 1
UNCONFIGURED    T4XXP (PCI) Card 0 Span 2
UNCONFIGURED    T4XXP (PCI) Card 0 Span 3
UNCONFIGURED    T4XXP (PCI) Card 0 Span 4

Span1 (Não sei interpretar essas informações)
Current Alarms:     No alarms.
Sync Source:        Internally clocked
IRQ Misses:               0
Bipolar Viol:             0
Tx/Rx Levels:         1/  0
Total/Conf/Act:      31/ 31/  0
     1111111111222222222333
1234567890123456789012345789012

astk:/etc# lspci -v
00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64
        Memory at <ignored> (64-bit, non-prefetchable)

00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00
[Normal decode])
        Flags: bus master, 66MHz, medium devsel, latency 99
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fde00000-fdefffff
        Prefetchable memory behind bridge: d8000000-dfffffff
        Capabilities: [b0] #0d [0000]

00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
(rev 80) (prog-if 8f [
Master SecP SecO PriP PriO])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185
        I/O ports at ff00 [size=8]
        I/O ports at fe00 [size=4]
        I/O ports at fd00 [size=8]
        I/O ports at fc00 [size=4]
        I/O ports at fb00 [size=16]
        Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
        [virtual] Expansion ROM at 80000000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 2
        Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
(rev 80) (prog-if 8f [
Master SecP SecO PriP PriO])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193
        I/O ports at fa00 [size=8]
        I/O ports at f900 [size=4]
        I/O ports at f800 [size=8]
        I/O ports at f700 [size=4]
        I/O ports at f600 [size=16]
        Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
        [virtual] Expansion ROM at 80080000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 2
        Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [
OHCI])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
        Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [
OHCI])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
        Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller
(rev 80) (prog-if 20
[EHCI])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
        Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [dc] Power Management version 2
        Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
        Subsystem: Intel Corporation Unknown device d600
        Flags: 66MHz, medium devsel
        I/O ports at 0b00 [size=16]
        Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]

00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
Controller ATI (rev 80)
 (prog-if 8a [Master SecP PriP])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 169
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at f400 [size=16]
        Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, slow devsel, latency 64, IRQ 169
        Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
        Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-

00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 0
astk:/etc# lspci -v
00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64
        Memory at <ignored> (64-bit, non-prefetchable)

00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00
[Normal decode])
        Flags: bus master, 66MHz, medium devsel, latency 99
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fde00000-fdefffff
        Prefetchable memory behind bridge: d8000000-dfffffff
        Capabilities: [b0] #0d [0000]

00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
(rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185
        I/O ports at ff00 [size=8]
        I/O ports at fe00 [size=4]
        I/O ports at fd00 [size=8]
        I/O ports at fc00 [size=4]
        I/O ports at fb00 [size=16]
        Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
        [virtual] Expansion ROM at 80000000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 2
        Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
(rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193
        I/O ports at fa00 [size=8]
        I/O ports at f900 [size=4]
        I/O ports at f800 [size=8]
        I/O ports at f700 [size=4]
        I/O ports at f600 [size=16]
        Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
        [virtual] Expansion ROM at 80080000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 2
        Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
        Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
        Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller
(rev 80) (prog-if 20 [EHCI])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
        Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [dc] Power Management version 2
        Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
        Subsystem: Intel Corporation Unknown device d600
        Flags: 66MHz, medium devsel
        I/O ports at 0b00 [size=16]
        Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]

00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
Controller ATI (rev 80) (prog-if 8a [Master SecP PriP])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 169
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at f400 [size=16]
        Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, slow devsel, latency 64, IRQ 169
        Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
        Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-

00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 0

00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
(prog-if 01 [Subtractive decode])
        Flags: bus master, VGA palette snoop, 66MHz, medium devsel, latency
64
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: fdd00000-fddfffff
        Prefetchable memory behind bridge: fdc00000-fdcfffff

01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress
200] (prog-if 00 [VGA])
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 5
        Memory at d8000000 (32-bit, prefetchable) [size=128M]
        I/O ports at ee00 [size=256]
        Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
        [virtual] Expansion ROM at fde00000 [disabled] [size=128K]
        Capabilities: [50] Power Management version 2
        Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-

02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Intel Corporation Unknown device d600
        Flags: bus master, medium devsel, latency 64, IRQ 201
        I/O ports at de00 [size=256]
        Memory at fddff000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2

02:04.0 Communication controller: Digium, Inc. Wildcard TE405P (2nd Gen)
(rev 02)
        Flags: bus master, medium devsel, latency 64, IRQ 209
        Memory at fddfe000 (32-bit, non-prefetchable) [size=128]

astk:/etc# uname -r   (Estou usando Debian)
2.6.16-2-686-smp


Essas configurações são as mesmas que funcionam em um Sempron 2400 e não
funcionam em um pentium 4 2.8. Testei esse fim de semana em um pentium III
1.0GHz (2 processadores) e funcionou normal também.
Qualquer idéia ou alguma informação a mais que seja necessária para tentar
resolver o problema é só mandar.

-- 
Ralph Liebessohn
ICQ: 74835911
Skype: liebessohn
-------------- Próxima Parte ----------
Um anexo em HTML foi limpo...
URL: http://listas.asteriskbrasil.org/pipermail/asteriskbrasil/attachments/20060814/7a2e2cea/attachment-0001.html


Mais detalhes sobre a lista de discussão AsteriskBrasil