Re: [AsteriskBrasil] digium card não funciona
Ralph Liebessohn
ralphliebessohn em gmail.com
Segunda Agosto 14 18:01:24 BRT 2006
On 8/14/06, Ralph Liebessohn <ralphliebessohn em gmail.com> wrote:
>
> On 8/14/06, Fabio Vasco <fabiohvgomes em hotmail.com> wrote:
> >
> > Ralph,
> > /etc/zaptel.conf e /etc/asterisk/zapata.conf
> > zttool
> > lspci -v
> > Deixa a gente ver isso...
> > Que Linux vc. está usando?
> > Abraços,
> > FHV
> >
> > >From: "Ralph Liebessohn" < ralphliebessohn em gmail.com>
> > >Reply-To: asteriskbrasil em listas.asteriskbrasil.org
> > >To: asteriskbrasil em listas.asteriskbrasil.org
> > >Subject: [AsteriskBrasil] digium card não funciona
> > >Date: Fri, 11 Aug 2006 16:50:28 +0000
> > >
> > >boa tarde,
> > >
> > >
> > >pessoal, estou com um probleminha aqui com uma placa da digium.
> > >Inicialmente comecei com o asterisk em um computador comum sempron com
> > >placa
> > >mãe pcchips e coloquei pra funcionar uma TE406P. Até ai tudo lindo.
> > >Agora colocando o asterisk pra rodar num P4 Dual com placa mãe intel
> > >(d101ggc) tudo aparentemente funciona, o asterisk compila, roda, liga
> > de
> > >sip
> > >pra sip, os modulos zaptel compilam, carregam, configuram, mas na hora
> > de
> > >ligar mesmo PAM !
> > >Recebo isso.
> > >
> > >Connected to Asterisk 1.2.7.1 currently running on astk (pid = 4174)
> > >Verbosity is at least 99
> > >Core debug is at least 99
> > > -- Executing Dial("SIP/12347-1574", "ZAP/g1/21226551") in new stack
> >
> > > -- Requested transfer capability: 0x00 - SPEECH
> > > -- Called g1/21226551
> > > == Primary D-Channel on span 1 down
> > >Aug 11 12:05:11 WARNING[4219]: chan_zap.c:2298 pri_find_dchan: No
> > >D-channels
> > >available! Using Primary channel 16 as D-channel anyway!
> > > -- Hungup 'Zap/1-1'
> > > == Everyone is busy/congested at this time (1:0/0/1)
> > > -- Executing Hangup("SIP/12347-1574", "") in new stack
> > > == Primary D-Channel on span 1 down
> > >Aug 11 12:05:14 WARNING[4219]: chan_zap.c:2298 pri_find_dchan: No
> > >D-channels
> > >available! Using Primary channel 16 as D-channel anyway!
> > >
> > >Saída /var/log/asterisk/full:
> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Allocating new SIP dialog for
> > >ff3e5bab-e0089797 em 192.168.11.192 - INVITE (With RTP)
> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: **** Received INVITE (5) -
> > Command
> > >in SIP INVITE
> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: * SIP extension value: 0 for
> > call
> > >ff3e5bab-e0089797 em 192.168.11.192
> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Setting NAT on RTP to 524288
> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: = Found Their Call ID:
> > >ff3e5bab-e0089797 em 192.168.11.192 Their Tag 53fbac9bdac9fb67o1
> > >Our tag: as0681a10d
> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: **** Received ACK (6) - Command
> > in
> > >SIP ACK
> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Stopping retransmission on '
> > > ff3e5bab-e0089797 em 192.168.11.192' of Response 101: Match
> > >Found
> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: = Found Their Call ID:
> > >ff3e5bab-e0089797 em 192.168.11.192 Their Tag 53fbac9bdac9fb67o1
> > >Our tag: as0681a10d
> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: **** Received INVITE (5) -
> > Command
> > >in SIP INVITE
> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: * SIP extension value: 0 for
> > call
> > >ff3e5bab-e0089797 em 192.168.11.192
> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Setting NAT on RTP to 524288
> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Checking SIP call limits for
> > device
> > >12347
> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Updating call counter for
> > incoming
> > >call
> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: build_route: Contact hop:
> > Linksys 2
> > ><sip:12347 em 192.168.11.192 :5061>
> > >Aug 11 11:53:31 DEBUG[4315] chan_sip.c: Checking device state for peer
> > >12347
> > >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for SIP/12347
> > -
> > >state 2 (In use)
> > >Aug 11 11:53:31 DEBUG[4610] pbx.c: Launching 'Dial'
> > >Aug 11 11:53:31 VERBOSE[4610] logger.c: -- Executing
> > >Dial("SIP/12347-d99a", "ZAP/g1/21226551") in new stack
> > >Aug 11 11:53:31 DEBUG[4610] chan_zap.c: Using channel 1
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable
> > >STACK-default-21226551-1.
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPCALLID.
> > >Aug 11 11:53:31 DEBUG[4610] channel.c : Not copying variable
> > SIPUSERAGENT.
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPDOMAIN.
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPURI.
> > >Aug 11 11:53:31 VERBOSE[4610] logger.c: -- Requested transfer
> > >capability: 0x00 - SPEECH
> > >Aug 11 11:53:31 VERBOSE[4610] logger.c: -- Called g1/21226551
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel Zap/1-1 to read
> > format
> > >slin
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel SIP/12347-d99a to
> > write
> > >format slin
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel SIP/12347-d99a to
> > read
> > >format slin
> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel Zap/1-1 to write
> > format
> > >slin
> > >Aug 11 11:53:31 DEBUG[4611] app_queue.c: Device 'SIP/12347' changed to
> > >state
> > >'2' (In use)
> > >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
> > state
> > >2 (In use)
> > >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
> > state
> > >2 (In use)
> > >Aug 11 11:53:31 DEBUG[4612] app_queue.c: Device 'Zap/1' changed to
> > state
> > >'2'
> > >(In use)
> > >Aug 11 11:53:31 DEBUG[4613] app_queue.c: Device 'Zap/1' changed to
> > state
> > >'2'
> > >(In use)
> > >Aug 11 11:53:31 DEBUG[4610] rtp.c: Ooh, format changed from unknown to
> > ulaw
> > >Aug 11 11:53:34 VERBOSE[4364] logger.c: == Primary D-Channel on span
> > 1
> > >down
> > >Aug 11 11:53:34 WARNING[4364] chan_zap.c: No D-channels
> > available! Using
> > >Primary channel 16 as D-channel anyway!
> > >Aug 11 11:53:34 DEBUG[4610] channel.c : Hanging up channel 'Zap/1-1'
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: zt_hangup(Zap/1-1)
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option AUDIO MODE, value:
> > ON(1)
> > >on Zap/1-1
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Hangup: channel: 1 index = 0,
> > >normal
> > >= 22, callwait = -1, thirdcall = -1
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: disabled echo cancellation on
> > >channel 1
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option TDD MODE, value:
> > OFF(0)
> > >on Zap/1-1
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Updated conferencing on 1, with
> > 0
> > >conference users
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option AUDIO MODE, value:
> > >OFF(0)
> > >on Zap/1-1
> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: disabled echo cancellation on
> > >channel 1
> > >Aug 11 11:53:34 VERBOSE[4610] logger.c: -- Hungup 'Zap/1-1'
> > >Aug 11 11:53:34 VERBOSE[4610] logger.c: == Everyone is busy/congested
> > at
> > >this time (1:0/0/1)
> > >Aug 11 11:53:34 DEBUG[4610] app_dial.c: Exiting with
> > >DIALSTATUS=CHANUNAVAIL.
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Launching 'Hangup'
> > >Aug 11 11:53:34 VERBOSE[4610] logger.c : -- Executing
> > >Hangup("SIP/12347-d99a", "") in new stack
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Spawn extension (default,21226551,2)
> > >exited non-zero on 'SIP/12347-d99a'
> > >Aug 11 11:53:34 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
> > state
> > >0 (Unknown)
> > >Aug 11 11:53:34 DEBUG[4614] app_queue.c: Device 'Zap/1' changed to
> > state
> > >'0'
> > >(Unknown)
> > >Aug 11 11:53:34 DEBUG[4610] cdr_pgsql.c: cdr_pgsql: inserting a CDR
> > record.
> > >Aug 11 11:53:34 DEBUG[4610] cdr_pgsql.c: cdr_pgsql: SQL command
> > executed:
> > >INSERT INTO cdr (calldate,clid,src,dst,dcontext,ch
> > >annel,dstchannel,lastapp,lastdata,duration,billsec
> > ,disposition,amaflags,accountcode,uniqueid,userfield)
> > >VALUES ('2006-08-11 1
> > >1:53:31','"Linksys 2" <12347>','12347','21226551','default',
> > >'SIP/12347-d99a','Zap/1-1','Hangup','',3,0,'NO ANSWER',2,'12347'
> > >,'1155308011.4','')
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '"Linksys 2"
> > <12347>'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '12347'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '21226551'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'default'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'SIP/12347-d99a'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'Zap/1-1'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c : Function result is 'Hangup'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '(null)'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '2006-08-11
> > 11:53:31'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c : Function result is '(null)'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '2006-08-11
> > 11:53:34'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '3'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '0'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'NO ANSWER'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'BILLING'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '12347'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '1155308011.4'
> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '(null)'
> > >Aug 11 11:53:34 DEBUG[4610] channel.c: Hanging up channel
> > 'SIP/12347-d99a'
> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: Hangup call SIP/12347-d99a, SIP
> >
> > >callid ff3e5bab-e0089797 em 192.168.11.192)
> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: update_call_counter(12347) -
> > >decrement call limit counter
> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: Updating call counter for
> > incoming
> > >call
> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: AST hangup cause 16 (no match
> > found
> > >in SIP)
> > >Aug 11 11:53:34 DEBUG[4315] chan_sip.c: Checking device state for peer
> > >12347
> > >Aug 11 11:53:34 DEBUG[4315] devicestate.c: Changing state for SIP/12347
> > -
> > >state 1 (Not in use)
> > >Aug 11 11:53:34 DEBUG[4615] app_queue.c: Device 'SIP/12347' changed to
> > >state
> > >'1' (Not in use)
> > >
> > >Ele simplesmente liga, chia e corta a ligação imediatamente, a partir
> > daí
> > >as
> > >ligações pelo E1 não se realizam mais.
> > >
> > >NOTICE[4981]: app_dial.c:1029 dial_exec_full: Unable to create channel
> > of
> > >type 'ZAP' (cause 34 - Circuit/channel congestion)
> > > == Everyone is busy/congested at this time (1:0/1/0)
> > >
> > >Receber ligação de forma nenhuma.
> > >As mesmas configurações (trocando o hd de máquina) funciona
> > perfeitamente.
> > >Já tentei usar também com outra placa intel e um p4 HT sem dual core,
> > mas a
> > >falha permaneceu.
> > >Já vi algumas coisas parecidas na lista mas nada que chegue ao amago
> > dessa
> > >questao.
> > >Alguem já viu algo parecido? Tem alguma idéia do que possa ser feito
> > para o
> > >sistema completo funcionar?
> > >
> > >
> > >--
> > >Ralph Liebessohn
> > >ICQ: 74835911
> > >Skype: liebessohn
> >
>
>
> Oi Fábio,
>
>
> vamos as configurações.
> astk:/etc# cat /etc/ zaptel.conf
>
> span=1,0,1,ccs,hdb3,crc4,yellow
> #span=2,0,1,ccs,hdb3,crc4,yellow
> #span=3,0,1,ccs,hdb3,crc4,yellow
> #span=4,0,1,ccs,hdb3,crc4,yellow
>
> bchan=1-15,17-31
> dchan=16
>
> #bchan=32-46,48-62
> #dchan=47
>
> #bchan=63-77,79-93
> #dchan=78
>
> #bchan=94-108,110-124
> #dchan=109
>
> loadzone = us
> loadzone = br
> defaultzone = br
>
>
> astk:/etc# cat /etc/asterisk/ zapata.conf
> [trunkgroups]
>
> [channels]
> context=default
> switchtype=national
> pridialplan=international
> ;signalling=pri_cpe
> rxwink=300 ; Atlas seems to use long (250ms) winks
> usecallerid=yes
> hidecallerid=no
> callwaiting=yes
> usecallingpres=yes
> callwaitingcallerid=yes
> threewaycalling=yes
> transfer=yes
> canpark=yes
> cancallforward=yes
> callreturn=yes
> echocancel=yes
> echocancelwhenbridged=yes
> echotraining=yes
> echotraining=400
> rxgain=0.0
> txgain=0.0
>
> group=1
> callgroup=1
> pickupgroup=1
> immediate=no
> transfertobusy=no
>
> signalling=pri_cpe
>
> channel => 1-15,17-31
> ;channel => 32-46,48-62,63-77,79-93
> ;channel => 94-108,110-124
>
> astk:/etc# zttool
> Alarms Span
> OK T4XXP (PCI) Card 0 Span 1
> UNCONFIGURED T4XXP (PCI) Card 0 Span 2
> UNCONFIGURED T4XXP (PCI) Card 0 Span 3
> UNCONFIGURED T4XXP (PCI) Card 0 Span 4
>
> Span1 (Não sei interpretar essas informações)
> Current Alarms: No alarms.
> Sync Source: Internally clocked
> IRQ Misses: 0
> Bipolar Viol: 0
> Tx/Rx Levels: 1/ 0
> Total/Conf/Act: 31/ 31/ 0
> 1111111111222222222333
> 1234567890123456789012345789012
>
> astk:/etc# lspci -v
> 00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64
> Memory at <ignored> (64-bit, non-prefetchable)
>
> 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00
> [Normal decode])
> Flags: bus master, 66MHz, medium devsel, latency 99
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: fde00000-fdefffff
> Prefetchable memory behind bridge: d8000000-dfffffff
> Capabilities: [b0] #0d [0000]
>
> 00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
> (rev 80) (prog-if 8f [
> Master SecP SecO PriP PriO])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185
> I/O ports at ff00 [size=8]
> I/O ports at fe00 [size=4]
> I/O ports at fd00 [size=8]
> I/O ports at fc00 [size=4]
> I/O ports at fb00 [size=16]
> Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
> [virtual] Expansion ROM at 80000000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
> (rev 80) (prog-if 8f [
> Master SecP SecO PriP PriO])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193
> I/O ports at fa00 [size=8]
> I/O ports at f900 [size=4]
> I/O ports at f800 [size=8]
> I/O ports at f700 [size=4]
> I/O ports at f600 [size=16]
> Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
> [virtual] Expansion ROM at 80080000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
> (rev 80) (prog-if 10 [
> OHCI])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
> Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
> (rev 80) (prog-if 10 [
> OHCI])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
> Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host
> Controller (rev 80) (prog-if 20
> [EHCI])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
> Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [dc] Power Management version 2
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
> Subsystem: Intel Corporation Unknown device d600
> Flags: 66MHz, medium devsel
> I/O ports at 0b00 [size=16]
> Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
>
> 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
> Controller ATI (rev 80)
> (prog-if 8a [Master SecP PriP])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 169
> I/O ports at <unassigned>
> I/O ports at <unassigned>
> I/O ports at <unassigned>
> I/O ports at <unassigned>
> I/O ports at f400 [size=16]
> Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00: 14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, slow devsel, latency 64, IRQ 169
> Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
> Enable-
>
> 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
>
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 0
> astk:/etc# lspci -v
> 00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64
> Memory at <ignored> (64-bit, non-prefetchable)
>
> 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00
> [Normal decode])
> Flags: bus master, 66MHz, medium devsel, latency 99
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: fde00000-fdefffff
> Prefetchable memory behind bridge: d8000000-dfffffff
> Capabilities: [b0] #0d [0000]
>
> 00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
> (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185
> I/O ports at ff00 [size=8]
> I/O ports at fe00 [size=4]
> I/O ports at fd00 [size=8]
> I/O ports at fc00 [size=4]
> I/O ports at fb00 [size=16]
> Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
> [virtual] Expansion ROM at 80000000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
> (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193
> I/O ports at fa00 [size=8]
> I/O ports at f900 [size=4]
> I/O ports at f800 [size=8]
> I/O ports at f700 [size=4]
> I/O ports at f600 [size=16]
> Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
> [virtual] Expansion ROM at 80080000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
> (rev 80) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
> Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
> (rev 80) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
> Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host
> Controller (rev 80) (prog-if 20 [EHCI])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
> Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [dc] Power Management version 2
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
> Subsystem: Intel Corporation Unknown device d600
> Flags: 66MHz, medium devsel
> I/O ports at 0b00 [size=16]
> Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
>
> 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
> Controller ATI (rev 80) (prog-if 8a [Master SecP PriP])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 169
> I/O ports at <unassigned>
> I/O ports at <unassigned>
> I/O ports at <unassigned>
> I/O ports at <unassigned>
> I/O ports at f400 [size=16]
> Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, slow devsel, latency 64, IRQ 169
> Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
> Enable-
>
> 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
>
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 0
>
> 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
> (prog-if 01 [Subtractive decode])
> Flags: bus master, VGA palette snoop, 66MHz, medium devsel,
> latency 64
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fdd00000-fddfffff
> Prefetchable memory behind bridge: fdc00000-fdcfffff
>
> 01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon
> Xpress 200] (prog-if 00 [VGA])
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 5
> Memory at d8000000 (32-bit, prefetchable) [size=128M]
> I/O ports at ee00 [size=256]
> Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
> [virtual] Expansion ROM at fde00000 [disabled] [size=128K]
> Capabilities: [50] Power Management version 2
> Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
>
> 02: 02.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+ (rev 10)
> Subsystem: Intel Corporation Unknown device d600
> Flags: bus master, medium devsel, latency 64, IRQ 201
> I/O ports at de00 [size=256]
> Memory at fddff000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
>
> 02:04.0 Communication controller: Digium, Inc. Wildcard TE405P (2nd Gen)
> (rev 02)
> Flags: bus master, medium devsel, latency 64, IRQ 209
> Memory at fddfe000 (32-bit, non-prefetchable) [size=128]
>
> astk:/etc# uname -r (Estou usando Debian)
> 2.6.16-2-686-smp
>
>
> Essas configurações são as mesmas que funcionam em um Sempron 2400 e não
> funcionam em um pentium 4 2.8. Testei esse fim de semana em um pentium III
> 1.0GHz (2 processadores) e funcionou normal também.
> Qualquer idéia ou alguma informação a mais que seja necessária para tentar
> resolver o problema é só mandar.
>
> --
>
> Ralph Liebessohn
> ICQ: 74835911
> Skype: liebessohn
>
Boa tarde.
Hoje me sugeriram retirar o módulo de cancelamento de eco da placa. E
funcionou.
Sem esse módulo parece estar tudo normal, vou realizar mais testes para
poder afirmar com certeza.
Obrigado pelo apoio.
--
Ralph Liebessohn
ICQ: 74835911
Skype: liebessohn
-------------- Próxima Parte ----------
Um anexo em HTML foi limpo...
URL: http://listas.asteriskbrasil.org/pipermail/asteriskbrasil/attachments/20060814/9c25892f/attachment-0001.html
Mais detalhes sobre a lista de discussão AsteriskBrasil