Re: [AsteriskBrasil] digium card não funciona

Fabio Vasco fabiohvgomes em hotmail.com
Terça Agosto 15 03:24:15 BRT 2006


Ralph, de onde surgiu a sugerencia de retirar o mod. de Echo Canc.???
Estranho... as configs. parecem estar todas OK. Será algum conflito com o 
seu mainboard?
Vc. chegou a falar com o pessoal da Digium?
Pagar pelo modulo e não poder usar é ruim hein...
Se vc. estiver usando o samples do Asterisk vc. terá o ramal 500 para se 
conectar com eles...
Senão adiciona isso no seu extensions.conf e liga lá... o suporte gratuito e 
direto da fonte... tenha em mãos os dados do seu servidor como IP Address e 
Root password... eles se conectam e revisam... :)
;
; Create an extension, 500, for dialing the
; Asterisk demo.
;
exten => 500,1,Playback(demo-abouttotry); Let them know what's going on
exten => 500,n,Dial(IAX2/guest em misery.digium.com/s em default)     ; Call the 
Asterisk demo
exten => 500,n,Playback(demo-nogo)      ; Couldn't connect to the demo site

Abraços,
FHV

>From: "Ralph Liebessohn" <ralphliebessohn em gmail.com>
>Reply-To: asteriskbrasil em listas.asteriskbrasil.org
>To: asteriskbrasil em listas.asteriskbrasil.org
>Subject: Re: [AsteriskBrasil] digium card não funciona
>Date: Mon, 14 Aug 2006 21:01:24 +0000
>
>On 8/14/06, Ralph Liebessohn <ralphliebessohn em gmail.com> wrote:
>>
>>On 8/14/06, Fabio Vasco <fabiohvgomes em hotmail.com> wrote:
>> >
>> > Ralph,
>> > /etc/zaptel.conf e /etc/asterisk/zapata.conf
>> > zttool
>> > lspci -v
>> > Deixa a gente ver isso...
>> > Que Linux vc. está usando?
>> > Abraços,
>> > FHV
>> >
>> > >From: "Ralph Liebessohn" < ralphliebessohn em gmail.com>
>> > >Reply-To: asteriskbrasil em listas.asteriskbrasil.org
>> > >To: asteriskbrasil em listas.asteriskbrasil.org
>> > >Subject: [AsteriskBrasil] digium card não funciona
>> > >Date: Fri, 11 Aug 2006 16:50:28 +0000
>> > >
>> > >boa tarde,
>> > >
>> > >
>> > >pessoal, estou com um probleminha aqui com uma placa da digium.
>> > >Inicialmente comecei com o asterisk em um computador comum sempron com
>> > >placa
>> > >mãe pcchips e coloquei pra funcionar uma TE406P. Até ai tudo lindo.
>> > >Agora colocando o asterisk pra rodar num P4 Dual com placa mãe intel
>> > >(d101ggc) tudo aparentemente funciona, o asterisk compila, roda, liga
>> > de
>> > >sip
>> > >pra sip, os modulos zaptel compilam, carregam, configuram, mas na hora
>> > de
>> > >ligar mesmo PAM !
>> > >Recebo isso.
>> > >
>> > >Connected to Asterisk 1.2.7.1 currently running on astk (pid = 4174)
>> > >Verbosity is at least 99
>> > >Core debug is at least 99
>> > >    -- Executing Dial("SIP/12347-1574", "ZAP/g1/21226551") in new 
>>stack
>> >
>> > >    -- Requested transfer capability: 0x00 - SPEECH
>> > >    -- Called g1/21226551
>> > >  == Primary D-Channel on span 1 down
>> > >Aug 11 12:05:11 WARNING[4219]: chan_zap.c:2298 pri_find_dchan: No
>> > >D-channels
>> > >available!  Using Primary channel 16 as D-channel anyway!
>> > >    -- Hungup 'Zap/1-1'
>> > >  == Everyone is busy/congested at this time (1:0/0/1)
>> > >    -- Executing Hangup("SIP/12347-1574", "") in new stack
>> > >  == Primary D-Channel on span 1 down
>> > >Aug 11 12:05:14 WARNING[4219]: chan_zap.c:2298 pri_find_dchan: No
>> > >D-channels
>> > >available!  Using Primary channel 16 as D-channel anyway!
>> > >
>> > >Saída /var/log/asterisk/full:
>> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Allocating new SIP dialog for
>> > >ff3e5bab-e0089797 em 192.168.11.192 - INVITE (With RTP)
>> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: **** Received INVITE (5) -
>> > Command
>> > >in SIP INVITE
>> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: * SIP extension value: 0 for
>> > call
>> > >ff3e5bab-e0089797 em 192.168.11.192
>> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Setting NAT on RTP to 524288
>> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: = Found Their Call ID:
>> > >ff3e5bab-e0089797 em 192.168.11.192 Their Tag 53fbac9bdac9fb67o1
>> > >Our tag: as0681a10d
>> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: **** Received ACK (6) - 
>>Command
>> > in
>> > >SIP ACK
>> > >Aug 11 11:53:30 DEBUG[4323] chan_sip.c: Stopping retransmission on '
>> > > ff3e5bab-e0089797 em 192.168.11.192' of Response 101: Match
>> > >Found
>> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: = Found Their Call ID:
>> > >ff3e5bab-e0089797 em 192.168.11.192 Their Tag 53fbac9bdac9fb67o1
>> > >Our tag: as0681a10d
>> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: **** Received INVITE (5) -
>> > Command
>> > >in SIP INVITE
>> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: * SIP extension value: 0 for
>> > call
>> > >ff3e5bab-e0089797 em 192.168.11.192
>> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Setting NAT on RTP to 524288
>> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Checking SIP call limits for
>> > device
>> > >12347
>> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: Updating call counter for
>> > incoming
>> > >call
>> > >Aug 11 11:53:31 DEBUG[4323] chan_sip.c: build_route: Contact hop:
>> > Linksys 2
>> > ><sip:12347 em 192.168.11.192 :5061>
>> > >Aug 11 11:53:31 DEBUG[4315] chan_sip.c: Checking device state for peer
>> > >12347
>> > >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for 
>>SIP/12347
>> > -
>> > >state 2 (In use)
>> > >Aug 11 11:53:31 DEBUG[4610] pbx.c: Launching 'Dial'
>> > >Aug 11 11:53:31 VERBOSE[4610] logger.c:     -- Executing
>> > >Dial("SIP/12347-d99a", "ZAP/g1/21226551") in new stack
>> > >Aug 11 11:53:31 DEBUG[4610] chan_zap.c: Using channel 1
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable
>> > >STACK-default-21226551-1.
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPCALLID.
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c : Not copying variable
>> > SIPUSERAGENT.
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPDOMAIN.
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Not copying variable SIPURI.
>> > >Aug 11 11:53:31 VERBOSE[4610] logger.c:     -- Requested transfer
>> > >capability: 0x00 - SPEECH
>> > >Aug 11 11:53:31 VERBOSE[4610] logger.c:     -- Called g1/21226551
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel Zap/1-1 to read
>> > format
>> > >slin
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel SIP/12347-d99a to
>> > write
>> > >format slin
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel SIP/12347-d99a to
>> > read
>> > >format slin
>> > >Aug 11 11:53:31 DEBUG[4610] channel.c: Set channel Zap/1-1 to write
>> > format
>> > >slin
>> > >Aug 11 11:53:31 DEBUG[4611] app_queue.c: Device 'SIP/12347' changed to
>> > >state
>> > >'2' (In use)
>> > >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
>> > state
>> > >2 (In use)
>> > >Aug 11 11:53:31 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
>> > state
>> > >2 (In use)
>> > >Aug 11 11:53:31 DEBUG[4612] app_queue.c: Device 'Zap/1' changed to
>> > state
>> > >'2'
>> > >(In use)
>> > >Aug 11 11:53:31 DEBUG[4613] app_queue.c: Device 'Zap/1' changed to
>> > state
>> > >'2'
>> > >(In use)
>> > >Aug 11 11:53:31 DEBUG[4610] rtp.c: Ooh, format changed from unknown to
>> > ulaw
>> > >Aug 11 11:53:34 VERBOSE[4364] logger.c:   == Primary D-Channel on span
>> > 1
>> > >down
>> > >Aug 11 11:53:34 WARNING[4364] chan_zap.c: No D-channels
>> > available!  Using
>> > >Primary channel 16 as D-channel anyway!
>> > >Aug 11 11:53:34 DEBUG[4610] channel.c : Hanging up channel 'Zap/1-1'
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: zt_hangup(Zap/1-1)
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option AUDIO MODE, value:
>> > ON(1)
>> > >on Zap/1-1
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Hangup: channel: 1 index = 0,
>> > >normal
>> > >= 22, callwait = -1, thirdcall = -1
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: disabled echo cancellation on
>> > >channel 1
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option TDD MODE, value:
>> > OFF(0)
>> > >on Zap/1-1
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Updated conferencing on 1, 
>>with
>> > 0
>> > >conference users
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: Set option AUDIO MODE, value:
>> > >OFF(0)
>> > >on Zap/1-1
>> > >Aug 11 11:53:34 DEBUG[4610] chan_zap.c: disabled echo cancellation on
>> > >channel 1
>> > >Aug 11 11:53:34 VERBOSE[4610] logger.c:     -- Hungup 'Zap/1-1'
>> > >Aug 11 11:53:34 VERBOSE[4610] logger.c:   == Everyone is 
>>busy/congested
>> > at
>> > >this time (1:0/0/1)
>> > >Aug 11 11:53:34 DEBUG[4610] app_dial.c: Exiting with
>> > >DIALSTATUS=CHANUNAVAIL.
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Launching 'Hangup'
>> > >Aug 11 11:53:34 VERBOSE[4610] logger.c :     -- Executing
>> > >Hangup("SIP/12347-d99a", "") in new stack
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Spawn extension 
>>(default,21226551,2)
>> > >exited non-zero on 'SIP/12347-d99a'
>> > >Aug 11 11:53:34 DEBUG[4315] devicestate.c: Changing state for Zap/1 -
>> > state
>> > >0 (Unknown)
>> > >Aug 11 11:53:34 DEBUG[4614] app_queue.c: Device 'Zap/1' changed to
>> > state
>> > >'0'
>> > >(Unknown)
>> > >Aug 11 11:53:34 DEBUG[4610] cdr_pgsql.c: cdr_pgsql: inserting a CDR
>> > record.
>> > >Aug 11 11:53:34 DEBUG[4610] cdr_pgsql.c: cdr_pgsql: SQL command
>> > executed:
>> > >INSERT INTO cdr (calldate,clid,src,dst,dcontext,ch
>> > >annel,dstchannel,lastapp,lastdata,duration,billsec
>> > ,disposition,amaflags,accountcode,uniqueid,userfield)
>> > >VALUES ('2006-08-11 1
>> > >1:53:31','"Linksys 2" <12347>','12347','21226551','default',
>> > >'SIP/12347-d99a','Zap/1-1','Hangup','',3,0,'NO ANSWER',2,'12347'
>> > >,'1155308011.4','')
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '"Linksys 2"
>> > <12347>'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '12347'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '21226551'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'default'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'SIP/12347-d99a'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'Zap/1-1'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c : Function result is 'Hangup'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '(null)'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '2006-08-11
>> > 11:53:31'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c : Function result is '(null)'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '2006-08-11
>> > 11:53:34'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '3'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '0'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'NO ANSWER'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is 'BILLING'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '12347'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '1155308011.4'
>> > >Aug 11 11:53:34 DEBUG[4610] pbx.c: Function result is '(null)'
>> > >Aug 11 11:53:34 DEBUG[4610] channel.c: Hanging up channel
>> > 'SIP/12347-d99a'
>> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: Hangup call SIP/12347-d99a, 
>>SIP
>> >
>> > >callid ff3e5bab-e0089797 em 192.168.11.192)
>> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: update_call_counter(12347) -
>> > >decrement call limit counter
>> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: Updating call counter for
>> > incoming
>> > >call
>> > >Aug 11 11:53:34 DEBUG[4610] chan_sip.c: AST hangup cause 16 (no match
>> > found
>> > >in SIP)
>> > >Aug 11 11:53:34 DEBUG[4315] chan_sip.c: Checking device state for peer
>> > >12347
>> > >Aug 11 11:53:34 DEBUG[4315] devicestate.c: Changing state for 
>>SIP/12347
>> > -
>> > >state 1 (Not in use)
>> > >Aug 11 11:53:34 DEBUG[4615] app_queue.c: Device 'SIP/12347' changed to
>> > >state
>> > >'1' (Not in use)
>> > >
>> > >Ele simplesmente liga, chia e corta a ligação imediatamente, a partir
>> > daí
>> > >as
>> > >ligações pelo E1 não se realizam mais.
>> > >
>> > >NOTICE[4981]: app_dial.c:1029 dial_exec_full: Unable to create channel
>> > of
>> > >type 'ZAP' (cause 34 - Circuit/channel congestion)
>> > >  == Everyone is busy/congested at this time (1:0/1/0)
>> > >
>> > >Receber ligação de forma nenhuma.
>> > >As mesmas configurações (trocando o hd de máquina) funciona
>> > perfeitamente.
>> > >Já tentei usar também com outra placa intel e um p4 HT sem dual core,
>> > mas a
>> > >falha permaneceu.
>> > >Já vi algumas coisas parecidas na lista mas nada que chegue ao amago
>> > dessa
>> > >questao.
>> > >Alguem já viu algo parecido? Tem alguma idéia do que possa ser feito
>> > para o
>> > >sistema completo funcionar?
>> > >
>> > >
>> > >--
>> > >Ralph Liebessohn
>> > >ICQ: 74835911
>> > >Skype: liebessohn
>> >
>>
>>
>>Oi Fábio,
>>
>>
>>vamos as configurações.
>>astk:/etc# cat /etc/ zaptel.conf
>>
>>span=1,0,1,ccs,hdb3,crc4,yellow
>>#span=2,0,1,ccs,hdb3,crc4,yellow
>>#span=3,0,1,ccs,hdb3,crc4,yellow
>>#span=4,0,1,ccs,hdb3,crc4,yellow
>>
>>bchan=1-15,17-31
>>dchan=16
>>
>>#bchan=32-46,48-62
>>#dchan=47
>>
>>#bchan=63-77,79-93
>>#dchan=78
>>
>>#bchan=94-108,110-124
>>#dchan=109
>>
>>loadzone = us
>>loadzone = br
>>defaultzone = br
>>
>>
>>astk:/etc# cat /etc/asterisk/ zapata.conf
>>[trunkgroups]
>>
>>[channels]
>>context=default
>>switchtype=national
>>pridialplan=international
>>;signalling=pri_cpe
>>rxwink=300              ; Atlas seems to use long (250ms) winks
>>usecallerid=yes
>>hidecallerid=no
>>callwaiting=yes
>>usecallingpres=yes
>>callwaitingcallerid=yes
>>threewaycalling=yes
>>transfer=yes
>>canpark=yes
>>cancallforward=yes
>>callreturn=yes
>>echocancel=yes
>>echocancelwhenbridged=yes
>>echotraining=yes
>>echotraining=400
>>rxgain=0.0
>>txgain=0.0
>>
>>group=1
>>callgroup=1
>>pickupgroup=1
>>immediate=no
>>transfertobusy=no
>>
>>signalling=pri_cpe
>>
>>channel => 1-15,17-31
>>;channel => 32-46,48-62,63-77,79-93
>>;channel => 94-108,110-124
>>
>>astk:/etc# zttool
>>Alarms          Span
>>OK              T4XXP (PCI) Card 0 Span 1
>>UNCONFIGURED    T4XXP (PCI) Card 0 Span 2
>>UNCONFIGURED    T4XXP (PCI) Card 0 Span 3
>>UNCONFIGURED    T4XXP (PCI) Card 0 Span 4
>>
>>Span1 (Não sei interpretar essas informações)
>>Current Alarms:     No alarms.
>>Sync Source:        Internally clocked
>>IRQ Misses:               0
>>Bipolar Viol:             0
>>Tx/Rx Levels:         1/  0
>>Total/Conf/Act:      31/ 31/  0
>>      1111111111222222222333
>>1234567890123456789012345789012
>>
>>astk:/etc# lspci -v
>>00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64
>>         Memory at <ignored> (64-bit, non-prefetchable)
>>
>>00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00
>>[Normal decode])
>>         Flags: bus master, 66MHz, medium devsel, latency 99
>>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
>>         I/O behind bridge: 0000e000-0000efff
>>         Memory behind bridge: fde00000-fdefffff
>>         Prefetchable memory behind bridge: d8000000-dfffffff
>>         Capabilities: [b0] #0d [0000]
>>
>>00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
>>(rev 80) (prog-if 8f [
>>Master SecP SecO PriP PriO])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185
>>         I/O ports at ff00 [size=8]
>>         I/O ports at fe00 [size=4]
>>         I/O ports at fd00 [size=8]
>>         I/O ports at fc00 [size=4]
>>         I/O ports at fb00 [size=16]
>>         Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
>>         [virtual] Expansion ROM at 80000000 [disabled] [size=512K]
>>         Capabilities: [60] Power Management version 2
>>         Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
>>(rev 80) (prog-if 8f [
>>Master SecP SecO PriP PriO])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193
>>         I/O ports at fa00 [size=8]
>>         I/O ports at f900 [size=4]
>>         I/O ports at f800 [size=8]
>>         I/O ports at f700 [size=4]
>>         I/O ports at f600 [size=16]
>>         Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
>>         [virtual] Expansion ROM at 80080000 [disabled] [size=512K]
>>         Capabilities: [60] Power Management version 2
>>         Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
>>(rev 80) (prog-if 10 [
>>OHCI])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
>>         Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
>>         Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
>>(rev 80) (prog-if 10 [
>>OHCI])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
>>         Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
>>         Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host
>>Controller (rev 80) (prog-if 20
>>[EHCI])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
>>         Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
>>         Capabilities: [dc] Power Management version 2
>>         Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: 66MHz, medium devsel
>>         I/O ports at 0b00 [size=16]
>>         Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
>>
>>00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
>>Controller ATI (rev 80)
>>  (prog-if 8a [Master SecP PriP])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 169
>>         I/O ports at <unassigned>
>>         I/O ports at <unassigned>
>>         I/O ports at <unassigned>
>>         I/O ports at <unassigned>
>>         I/O ports at f400 [size=16]
>>         Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00: 14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, slow devsel, latency 64, IRQ 169
>>         Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
>>         Capabilities: [50] Power Management version 2
>>         Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
>>Enable-
>>
>>00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
>>
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 0
>>astk:/etc# lspci -v
>>00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64
>>         Memory at <ignored> (64-bit, non-prefetchable)
>>
>>00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00
>>[Normal decode])
>>         Flags: bus master, 66MHz, medium devsel, latency 99
>>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
>>         I/O behind bridge: 0000e000-0000efff
>>         Memory behind bridge: fde00000-fdefffff
>>         Prefetchable memory behind bridge: d8000000-dfffffff
>>         Capabilities: [b0] #0d [0000]
>>
>>00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
>>(rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185
>>         I/O ports at ff00 [size=8]
>>         I/O ports at fe00 [size=4]
>>         I/O ports at fd00 [size=8]
>>         I/O ports at fc00 [size=4]
>>         I/O ports at fb00 [size=16]
>>         Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
>>         [virtual] Expansion ROM at 80000000 [disabled] [size=512K]
>>         Capabilities: [60] Power Management version 2
>>         Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
>>(rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193
>>         I/O ports at fa00 [size=8]
>>         I/O ports at f900 [size=4]
>>         I/O ports at f800 [size=8]
>>         I/O ports at f700 [size=4]
>>         I/O ports at f600 [size=16]
>>         Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
>>         [virtual] Expansion ROM at 80080000 [disabled] [size=512K]
>>         Capabilities: [60] Power Management version 2
>>         Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
>>(rev 80) (prog-if 10 [OHCI])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
>>         Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
>>         Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
>>(rev 80) (prog-if 10 [OHCI])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
>>         Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
>>         Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host
>>Controller (rev 80) (prog-if 20 [EHCI])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177
>>         Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
>>         Capabilities: [dc] Power Management version 2
>>         Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: 66MHz, medium devsel
>>         I/O ports at 0b00 [size=16]
>>         Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
>>
>>00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
>>Controller ATI (rev 80) (prog-if 8a [Master SecP PriP])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 169
>>         I/O ports at <unassigned>
>>         I/O ports at <unassigned>
>>         I/O ports at <unassigned>
>>         I/O ports at <unassigned>
>>         I/O ports at f400 [size=16]
>>         Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, slow devsel, latency 64, IRQ 169
>>         Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
>>         Capabilities: [50] Power Management version 2
>>         Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
>>Enable-
>>
>>00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
>>
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 0
>>
>>00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
>>(prog-if 01 [Subtractive decode])
>>         Flags: bus master, VGA palette snoop, 66MHz, medium devsel,
>>latency 64
>>         Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
>>         I/O behind bridge: 0000d000-0000dfff
>>         Memory behind bridge: fdd00000-fddfffff
>>         Prefetchable memory behind bridge: fdc00000-fdcfffff
>>
>>01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon
>>Xpress 200] (prog-if 00 [VGA])
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 5
>>         Memory at d8000000 (32-bit, prefetchable) [size=128M]
>>         I/O ports at ee00 [size=256]
>>         Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
>>         [virtual] Expansion ROM at fde00000 [disabled] [size=128K]
>>         Capabilities: [50] Power Management version 2
>>         Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
>>Enable-
>>
>>02: 02.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
>>RTL-8139/8139C/8139C+ (rev 10)
>>         Subsystem: Intel Corporation Unknown device d600
>>         Flags: bus master, medium devsel, latency 64, IRQ 201
>>         I/O ports at de00 [size=256]
>>         Memory at fddff000 (32-bit, non-prefetchable) [size=256]
>>         Capabilities: [50] Power Management version 2
>>
>>02:04.0 Communication controller: Digium, Inc. Wildcard TE405P (2nd Gen)
>>(rev 02)
>>         Flags: bus master, medium devsel, latency 64, IRQ 209
>>         Memory at fddfe000 (32-bit, non-prefetchable) [size=128]
>>
>>astk:/etc# uname -r   (Estou usando Debian)
>>2.6.16-2-686-smp
>>
>>
>>Essas configurações são as mesmas que funcionam em um Sempron 2400 e não
>>funcionam em um pentium 4 2.8. Testei esse fim de semana em um pentium III
>>1.0GHz (2 processadores) e funcionou normal também.
>>Qualquer idéia ou alguma informação a mais que seja necessária para tentar
>>resolver o problema é só mandar.
>>
>>--
>>
>>Ralph Liebessohn
>>ICQ: 74835911
>>Skype: liebessohn
>>
>
>
>Boa tarde.
>Hoje me sugeriram retirar o módulo de cancelamento de eco da placa. E
>funcionou.
>Sem esse módulo parece estar tudo normal, vou realizar mais testes para
>poder afirmar com certeza.
>Obrigado pelo apoio.
>
>--
>Ralph Liebessohn
>ICQ: 74835911
>Skype: liebessohn


>_______________________________________________
>LIsta de discussões AsteriskBrasil.org
>AsteriskBrasil em listas.asteriskbrasil.org
>http://listas.asteriskbrasil.org/mailman/listinfo/asteriskbrasil
>
>_______________________________________________
>Acesse o  wiki AsteriskBrasil.org:
>http://www.asteriskbrasil.org

_________________________________________________________________
MSN Busca: fácil, rápido, direto ao ponto.  http://search.msn.com.br



Mais detalhes sobre a lista de discussão AsteriskBrasil